Messages

1

iCam Support / Re: iCamSource stop streaming

« on: October 12, 2010, 06:10:02 PM »

.

2

iCam Support / Re: iCamSource stop streaming

« on: October 12, 2010, 05:06:14 PM »

QQVGA at 20 fps works but the resolution is really bad as it will blow a large screen from a very small intake.

But full VGA at 5 (even 15 in my case) made the trick. Been running for the last 24 hrs. BTW this is a great application when working.

So my problem is fixed. Many thanks for helping. I now have a confirmation my processing capability is limited. I will eventually need to upgrade it.

Do you have any recommandation or suggestion about an optimal processor or computer configuration?

Thanks again for helping.

3

iCam Support / Re: iCamSource stop streaming

« on: October 11, 2010, 04:51:22 PM »

It is currently at VGA 25 fps which is probably the by default setup. Could setup to QVGA or QQVGA and from 1 to 30 fps. I am not familiar with the QQVGA appelation, I am not sure if better or low resolution than VGA.

Do you have a proposed setup?

4

iCam Support / Re: iCamSource stop streaming

« on: October 11, 2010, 02:32:22 PM »

Thanks for helping.

I am not sure if the problem is caused by a "not capable enough" processor or if it is something else.

But by removing recognition option and putting the resolution to a minimum, even if the processsing is limited, it will keep going at least with iCamSource. If I add recognition, it crashes.

But with or without recognition, it will lose connection with Icam after a couple of minute. I am not sure why.

Thanks

5

iCam Support / Re: iCamSource stop streaming

« on: October 11, 2010, 06:26:53 AM »

IE or Firefox? If you refer to post #3, my problem is that I am able to connect two SkyIPcam500 to iCamSource then look at them through ICam but not for more than a minute or two before it crash.

Thanks for your help.

6

iCam Support / Re: iCamSource stop streaming

« on: October 10, 2010, 05:46:36 PM »

Sorry for the delay. Was out of town.

If I go to the http://192.168.2.241/cgi/mjpg/mjpeg.cgi  URL in my web browser, I'm being asked the username and password. After this step, I'm being asked if I want to download MJPEG.CGI from 192.168.2.240.

BTW, I am able to get back connections to both camera through IcamSource, but I am also back with the previous problem of losing streaming after a one minute or so.

Thanks for your help.
 

7

iCam Support / Re: iCamSource stop streaming

« on: October 09, 2010, 05:07:42 AM »

One camera same behavior as two.

I am currently using http://192.168.2.241/cgi/mjpg/mjpeg.cgi (240/241 depending on the camera). I tried keeping this but with JPEG. Doesn't work. Loose the camera connection.

Tried with the only option in JPEG (at least listed on your site) with http://192.168.2.240/goform/capture with the JPEG option. No communication.

UPDATE: doesn't want to reconnect using previous setup (http://192.168.2.241/cgi/mjpg/mjpeg.cgi with MJPEG option)! Weird.

8

iCam Support / Re: iCamSource stop streaming

« on: October 08, 2010, 03:31:52 PM »

I have the exact same problem (at least I think...)

I have two SkyIPcam500 hardwired.

Icamsource is on an AMD Athlon 64 X2 Dual Core 3800- processor based computer.

No problem logging in Icamsource. Will connect on Icam for a couple of minute before "losing the communication". The Icamsource still have an image but it seems frozen.

The Airlink view would still work properly. I disable completely the recognition part and put the less precise image possible.

When I start Icamsource, the processor is usually around 30%. Then after a 1 minute it will go to the roof (99-100%). Will go to the roof with only one camera. At this point, since the recognition is disable, all it does is retransmitting an image.

I though it was because my computer is not fast enough. But Airlink view alone seems fine with my processing capability. Seems more like an infinite loop somewhere...

Any idea?

Thanks