Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Druv3us

Pages: [1]
1
iCam Support / Re: DSC-930L issue
« on: October 08, 2014, 08:09:19 PM »
I've reset the camera and now it has no login or password.

I went to the site and the login drop down menu still drops down.
I click log in and it drops down again.
I click log in until it stops dropping down.
Beside each link it says error file not found

http://skjm.com/forum/index.php?topic=1847.0

They say it works.

Any other help would be great.
It seems Icamsource is the only app I can find that takes snapshots on motion.
I'm remaining hopeful

By the way, now the icam gui says 401 - Webcam Authorization failure - Please make sure that the Camera Login and Password are correct and try again.

2
iCam Support / Re: DSC-930L issue
« on: October 07, 2014, 11:09:37 PM »
The drop down menu keeps popping up when I try to input a login and password.
I have to keep clicking cancel until all the links listed below load a question mark in a blue square.

The iCam site says the D-Link camera is compatible.
There must be something missing.

Any help?

Drew

3
iCam Support / Re: DSC-930L issue
« on: October 07, 2014, 08:55:06 AM »
When I go to the page
http://skjm.com/icam/mjpeg_test.php
I tells me to put in my IP and port (the port is already typed as 80)
when I put in my IP address a drop down menu says,

To view this page, you must log in to area "DCS-930L" on 192.168.1.14:80

Name:
Password:

I made my password simple so I don't screw it up while in this set up phase and still nothing.

I don't know what I'm missing here. I'm knowledgeable enough with computers to know that this should be working by now.
Drew

4
iCam Support / Re: DSC-930L issue
« on: October 06, 2014, 08:03:27 PM »
Hi OUAnthony

Thank you for your post.
I'm sadly a little lost at what the website wants from me.
When I go to this site
http://skjm.com/icam/mjpeg_test.php
to see if I can get my camera to work with Icamsource it has a drop down menu asking for the
Name and Password
I've as far as renaming the name and password to camera and camera (I'll change that if and when I get this working)

I just want to get my DCS-930L to take pictures like I can get from the webcam in my mac.

If you can tell me exactly how I'm to do that I'll be eternally grateful.

Drew

5
iCam Support / Re: DSC-930L issue
« on: October 06, 2014, 01:17:50 PM »
Any help would be great.
I have a limited time to return the camera if it wont work with your app.

Drew

6
iCam Support / Re: DSC-930L issue
« on: October 04, 2014, 01:35:35 PM »
I've tried to put in [login]
and [password]@Camera_address

Doesn't accept it

7
iCam Support / Re: DSC-930L issue
« on: October 04, 2014, 08:30:25 AM »
Thanks for the reply

I typed in the address but I'm unclear about what you want me to do with the password@Camera_address pasword etc.


8
iCam Support / DSC-930L issue
« on: October 03, 2014, 12:08:28 PM »
Hi Guys;

I'm new to the forum.

I have a netgear router and a d-link DSC-930L camera
I've got the camera set up in my network fine.
I can log into the D-link site and see what the camera sees through their site.
I added the DSC-930L to Icamsource but it doesnt work yet.

The GUI keeps telling me "Your network IP camera could not be connected to. Please make sure the Camera URL contains the network address for your camera"
I have the 192.168.xxx.xxx. etc correct and the Camera login and the Camera password are correct too.

Am I missing something?
Any help would be great.
Thanks
Druv3us


Pages: [1]