Messages

1

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 20, 2011, 03:31:21 PM »

HEY, THANKS FOR ALL YOUR HELP! I tried one last thing yesterday and it WORKED! i updated the firmware on my Apple router. i hadn't done that in about 2 years. the portchecker site still says its blocked but it works anyway. so i am not going to sweat that little fact. i am so happy with the program now. i hope this post will help someone else with the same problem....you rock!

2

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 07:15:20 PM »

updated my software on airport base station wireless router. i did what you said above and it now says, NAT-PMP Success 12000->12000.  but when i do your port checker it still comes back with this  UDP Port 12001 is BLOCKED

3

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 07:09:16 PM »

already did that today. anything else?

4

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 11:21:38 AM »

try this if you cant see the grabs

5

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 11:19:43 AM »

here are two screen grabs. one connected wireless an done connected directly to router.

6

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 10:50:18 AM »

says it's open when plugging directly from the router to my computer.

7

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 10:47:03 AM »

okay it says it is blocked.

8

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 17, 2011, 09:19:56 AM »

the router was supplied by my local cable company ( Comcast ). that is plugged into my wireless base station from Apple which throws out the wireless signal. i guess thry plugging it in directly and see if it works? oris there another test we can run without going through all that?

9

iCam Support / Re: ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 16, 2011, 09:02:55 AM »

arris tm502g

once again thanks

10

iCam Support / ICAM worx on WIFI at home with Itouch and Isight but doesn't work on remote WIF

« on: June 15, 2011, 03:22:10 PM »

Hey Guys,

First of all....great app!
works fine at home over wifi on ipod itouch 4th generation.
i am running your software on a brand new isight mac and using the isight camera with it.
when i log in remotely over WIFI i get the broker error message. it's weird i do get motion detected messages. but no picture no sound and the broker message though.
i get this message on my home computer. error: UPnP 0 : NAT-PMP 3,-7,61
any thoughts?

i tried this per your suggestion as well. i couldn't figure out
http://portforward.com/english/routers/port_forwarding/Arris/TM502b/default.htm

i also tried to set the static IP address. http://portforward.com/networking/static-Mac10.4.htm
maybe if you have a mac solution to this. the port forward site direction images look different on my computer. i guess because i am running 10.6 and their's is 10.4


thanks in advance,

matt