Topics

1

iCam Pro Support / Is Support DEAD on this forum???

« on: May 28, 2020, 08:44:49 AM »

Just wondering if support is offered here anymore.

I left a message on Feb 08 asking about a problem on the iCam forum and it was never replied to;

I upgraded to the iCam Pro app to see if that would work better and I posted a issue this week that I am having with it and I received no response.

Been a user since 2011, please tell me if it is time to move on.

Regards

2

iCam Pro Support / iCamSourcePro.exe has stopped working error

« on: May 25, 2020, 07:24:37 AM »

Been a long time iCam user and upgraded to the windows pro version and it seems after a few hours of working, it just stops.

It is either icamsourcepro is not responding or iCamsourcePro.exe has stopped working.

Any ideas as what could be causing this? Using version 1.3.1.1

Thank you

Ponti

3

iCam Support / iCam stops working, have to reboot pc

« on: February 05, 2020, 05:54:09 PM »

Any suggestions for the following problem.

iCam has been rock solid for the years I've used it.

It seems I have to reboot every day to get the cameras to show on the iphone. 

The wifi cameras are showing on icam source that is running on the pc but not on my phone.

I reboot the  windows pc and start icam source and everything is fine, but it seems the next day I cant view the cameras on the phone.

I reboot again and everything is fine until the next day.

Any ideas? I have reinstalled icam source 2.9 and this doesn't help.

Thank you in advance

Ponti

4

iCam Support / Help with Amcrest IPM-721 or did I just throw my money away

« on: July 12, 2018, 05:12:02 PM »

Been using Icam for years and one of my Tenvis cameras just died. 

I did some searching on these forums and saw a thread about the Amcrest cameras.  Even though they were H264 there was a thread the newer cameras had MJPEG also.
So I received it today and am having difficulty getting it to work with icam.

I see in the settings under enable substream a drop down box that has MJPEG for encode mode.  I have tried changing this, but I get error messages in Icam source.  Is this the stream I need? Any suggestions on how to access this stream?

Am I out of luck or has anyone gotten the Amcrest to work?

Thanks for any info

Jim

5

iCam Support / Icamsource 2.7.2 Stopped recording

« on: January 02, 2018, 05:15:17 PM »

Hello,

Longtime iCam user. A few days ago, I noticed my icam app is not recording.  My last recording on my 3 cameras was 12/09/17.

I have run cleanicamkey.reg a few times and reinstalled 2.7.2 and my cams will send notifications, but will not record.

I have record motion selected on the app.

I  try and download a newer version and I keep getting "not a valid win32" error so 2.7.2 is the latest I am able to find and install without a Win32 error.

I am using XP professional service pack 3 with over 10 gig of free space.

Any help will be appreciated.

Thank you

6

iCam Support / iCamWeb stopped working for me

« on: April 21, 2011, 03:39:53 AM »

I have been using iCam and loving it for some time now and never had any problems.  I came home yesterday and noticed I did not have any internet service.  Long story short rebooted my router and now have a new IP address.   iCam works fine on my iphone, but can no longer use iCamWeb.  It finds the sources as I have four cameras, then I get the following error for each camera

Source connection error.. one or more cameras......

Any help will be appreciate.

Jim