Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Merlin

Pages: 1 [2] 3 4 ... 8
16
iCam Support / Re: Airport Extreme 5th Generation 7.6.4
« on: September 03, 2013, 01:08:59 PM »
I am able to connect now with all my cameras.  5 home and 1 work. 

Merlin

17
iCam Support / Re: Airport Extreme 5th Generation 7.6.4
« on: September 01, 2013, 12:11:01 PM »
Glad to help...
Merlin

18
iCam Support / Re: Airport Extreme 5th Generation 7.6.4
« on: August 31, 2013, 06:15:45 PM »
Okay I reset my Airport Extreme and redid everything.  I am aware of the Enable Port Mapping Protocol and had it enabled before.  All Ports are forwarded for all the cameras except the USB camera.  All cameras are on a fixed IP except for again the USB camera.  I did however change the computer running iCamSource to a fixed IP address...just in case. 
Enabled Port Mapping
Each camera has it's own port
Forwarded all ports related to cameras
Forwarded iCamSource port range of 12000-12100
Even though I have the ports forwarded I do have the Auto Configure Router box checked
I do not have the box for Enable Public Proxy checked at this time
I can see all cameras through Wi-Fi and through LTE
The only thing I am worried about is the message;
"NAT-PMP Success 12003 thru 12003NAT-PMP TIMEOUTNAT-PMP TIMEOUT"
What does this now mean?

Merlin

19
iCam Support / Re: Airport Extreme 5th Generation 7.6.4
« on: August 30, 2013, 02:02:42 PM »
Before I update I had no issues with my cameras.  Now that I have updated I get UPnP may not be enabled although I have UPnP enabled on my Apple Airport Extreme.  Further it seems that only one of my 5 cameras is only viewable on iCamSource either on Wi-Fi or on LTE.  Also I do have all my ports forwarded for each camera on the system except the USB camera on my computer.

Puzzled,
Merlin

20
iCam Support / Airport Extreme 5th Generation 7.6.4
« on: August 28, 2013, 09:44:06 PM »
Every since I updated to version 7.6.4 I have had issues with iCamSource.  Is anyone else having issues?

Merlin

21
iCam Support / Re: New Releases : iCam 2.3 (iOS) & iCamSource 2.7
« on: July 22, 2013, 04:38:16 PM »
I just wanted to make sure I understood.  If I enable the Proxy option, will it always try Peer to Peer first?  I only would want to do Proxy if Peer to Peer failed.

Thanks,
Merlin

22
iCam Support / Logitech QuickCam Orbit AF
« on: June 30, 2013, 08:47:48 PM »
Does anyone have the Orbit AF and could help me?  The camera picture looks great as long as there is not any movement.  When there is movement the picture is blurry and the person cannot be made out.  Is there a way to slow the frame rate down on Logitech WebCams?  Does anyone else have this same issue?

Thanks,
Merlin

23
iCam Support / Password Change
« on: June 10, 2013, 02:37:44 PM »
How long does it take for a password change to take effect to view your feeds?

Merlin

24
My iCamSource crashes periodically.  Does SKJM want the crash logs?  Windows also periodically checks for solutions and submits the crash logs to Windows and it never finds a solution.  Do these crash logs go to SKJM for their review?  Periodically is once a week or so...I use Jumi to log on to my computer and either reboot the computer or just restart iCamSource.

Merlin

25
iCam Support / Playback on My Network
« on: April 09, 2013, 09:40:14 PM »
I don't know if anyone else has this issue, but when I play back an event when I'm on my network it moves so fast that I can't get a good look at people or what is happening.  It is almost a blur.  However on 4G it plays back at a steady rate.  I know that I can view it slower by using the manual process using the arrows, but it would seem that a play back speed could be set for viewing motion events.

Merlin

26
Back to the original issue that nyvin posted...I have been having the same issue for some time as well.  If I have iCamSource as a task or even in the startup folder and the Auto-Start Checked, when the computer reboots it says Connecting....  The cameras don't connect.  If someone just toggles the Start button everything connects.  A while back I installed Jumi to be able to toggle the Start so that the cameras would work. 
I often wonder though what would happen if the Auto-Start had a delay feature that could be set for 1 to 5 minutes.  Just a thought...

Merlin

27
iCam Support / Re: iCamSource memory leak?
« on: March 21, 2013, 06:18:23 AM »
I have to admit I was very skeptical about lowering my cameras to 2 FPS, but I tried it.  They have been going for more than 3 days and I have been very pleased with the results and the reduction in CPU usage.  RAM usage appears to be the same.  Because of all this I have added a fifth camera.   ;D  There have been numerous people caught at my front door and walking in my driveway and the frame rate or capture rate appears to be same as when I had it set at 3 FPS.

Merlin

28
iCam Support / Re: iCamSource memory leak?
« on: March 16, 2013, 11:47:56 PM »
Dropped cameras and dropped frames the higher the CPU.  I also have the frame rate at 3 fps right now.  I see the action on the computer but what records is less.  Again both issues when CPU usage is at it's highest.

Merlin

29
iCam Support / Re: iCamSource memory leak?
« on: March 16, 2013, 11:18:23 AM »
For my system: copying your format ouanthony

3 Cisco Linksys-N WVC80N
1 AIRLINK101 AICN777W

Average CPU usage was 35-60% and RAM usage around 37-55MB.

Dropbox has low CPU usage (<5%), and uses around 40MB of RAM.

My total physical memory being used is often more than 52% (of 4GB).

Hope that helps...
Merlin

30
Beta Testing / Re: Request for new feature
« on: December 11, 2012, 07:48:31 PM »
WOW AGAIN someone just won't stop!  and I thought there was an actual update since someone posted on the update page.  Sorry just thought there was a new beta version...I'll stop   :)

Pages: 1 [2] 3 4 ... 8