Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Berlingoman

Pages: [1]
iCam Pro Support / Where is icamsource mobile events saved?
« on: May 16, 2017, 01:20:36 PM »
Where is icamsource mobile events saved? I have also icamsource for pc running and would like to know where it saves mobile events ... maybe i would like to backup to icamsource pc place ...


I would like to enable or diasable a camera in iCamSource Pro please then i would not need to setup each time :-). Or maybe the other way around in iCamPro i would like to be able to choose which camera i would like to watch :-) Or maybe both places ;-)

See my suggestion image here:!AvDwxm29ITA2zaEgtBtOywcMD9g60A

iCam Pro Support / Move iCamSource pro to other PC? - Urgent :-)
« on: October 24, 2016, 10:05:45 AM »

Is there a way to move iCamSource pro settings to a new PC?

iCam Pro Support / Connection closed
« on: March 24, 2016, 09:50:39 AM »
I get connection closed within 1 sec. on 2 iPhones running 4g mobile data remote... When sharing internet from the iphone to a ipad the ipad icam pro works fine?! I tried to reinstall iphone icam pro but same issue?!
I tried both with and without proxy... I payed for both service and proxy...


Question 1 Will this setting be OK in icamsource pro?: - i have problem loosing connection after af short while with "iCam broker server..."  especially to my wifi cameras, the webcam on pc running on icamsource pc is connected ok. the error i see is on ipad iCam on same wifi net. All cameras shown fine when  connection tested through browser on  icamsource pc when using external-ip:8003 ?

Question 2 I have payed for 25MB proxy data - how can I see when its used ?

I look forward for a answer :-)

iCam Support / Re: Error code 11 - iCam wont start
« on: June 14, 2012, 01:17:36 PM »
Workaround found for me !! i also did "everything" without succes - uninstalling etc. but then:

Even though getting Error code 11 at startup of icamsource i maneged to right click icamsource icon in taskbar a going to preference let me open program and stopping + removing bad usb camera for my list. Then able to start icamsource without error 11. This i think should be possible to correct in program!?

Beta Testing / Re: iCamSource 2.4.7 BETA - Notification Threshold
« on: June 12, 2012, 03:45:51 PM »
Thanks a lot for fast develop - i Will test  this new feature  :)

Beta Testing / Re: iCamSource 2.4.6 BETA - Motion Event Image Minimum
« on: June 05, 2012, 10:45:46 AM »
Yes and you are allready looking into it:

"We are looking into thresholding motion detection for push notifications as well. The logic we will have to use will be different than what we implemented for the recording of motion events, but it should still give users the desired control over their notifications."

I'm happy about the option to leave out 1-2 etc. frames but the program would be even better when option to not be notified about these also.

Beta Testing / Re: iCamSource 2.4.6 BETA - Motion Event Image Minimum
« on: June 05, 2012, 01:16:54 AM »
I would love this fixed  ;D

iCam Support / Re: Feature request(s) re: motion event logging
« on: May 29, 2012, 03:57:21 PM »
And no not possible to make less sensitive etc.

iCam Support / Re: Feature request(s) re: motion event logging
« on: May 29, 2012, 03:53:24 PM »
Too many 1 or 2 pics -Would be Nice to have a filter /search option so that etc. all 1 or 2 Pic  Could be left out when browsing log.

Pages: [1]