SKJM Forum

Support => iCam Support => Topic started by: Stefan on December 07, 2008, 12:51:43 PM

Title: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Stefan on December 07, 2008, 12:51:43 PM
If you are receiving the iCam "Cannot Connect To iCam Broker Server. Please try again later." error message when trying to connect via EDGE or 3G, here is one thing you can try: Open another iPhone network application (such as Stocks or Weather) and then see if iCam works after that.

This is a strange issue that we cannot reproduce but a small number of users have reported having. If you are among them (and running Stocks or Weather fixes the issue until you restart your iPhone) please post your experiences here or contact support@skjm.com.

Thanks!  :)
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G
Post by: Stefan on December 07, 2008, 04:13:39 PM
UPDATE

If, when you run iCam when it is connecting over 3G or EDGE and you repeatedly see the following message: "Connection Error - There was an error connecting to the iCam Broker Server. Please try again later." we have made progress in tracking this problem down.

When you see this error message, if you then open another iPhone network application like Stocks or Weather and are then able to connect via iCam, then this is a bug that we are aware of and are now able to reproduce.

I do have a question, however: In your iPhone settings, under Fetch New Data, do you have Push enabled? Also, what is your Fetch schedule setting (15 min, 30 min, 1 hour, or manual)? Currently when I disable Push on my iPhone and set the Fetch to Manual, I can reproduce the error message after letting my iPhone sit idle for a few minutes.

The assumption is that the iPhone most likely disengages its connection with the cellular network after a period of inactivity, and therefore when iCam starts up, it is unable to access the internet. I assume that the iPhone does not re-enable the 3G internet connection when it attempts to contact the Broker Server via UDP ... That is why running an application that uses TCP connections causes iCam to subsequently work.

We are looking into a solution to this problem that is more elegant than the current one of having you run another network application before running iCam. I anticipate it to be included in the upcoming 1.0.3 iCam release that should be available in the App Store within the next week or so.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: syousuff on December 07, 2008, 06:48:12 PM
I just bought the app today. I am getting the error message "Connection Error - There was an error connecting to the iCam Broker Server. Please try again later."  I am experiencing this over a strong WiFi connection, not Edge or 3G as previously reported. I also have Push enabled and Fetch set to every 15 minutes. Stocks and Weather both work perfectly when I tried launching these before iCam.

I have a Macbook Pro C2D 2.33 GHz, 3GB RAM running 10.5.5. My husband installed iCam source on his Macbook running 10.5.5 (to see if there was a problem with our network) and I had no problems connecting to his iSight with iCam.

I tried uninstalling/reinstalling the app as well -- no success.

Any ideas on how to fix the problem?
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.3
Post by: Stefan on December 08, 2008, 06:49:41 AM
syousuff - After checking the Broker Server logs it seems like your iPhone and MBP have the same external IP (are behind the same router) but have a different class of internal IP (10.0.1.xxx vs. 192.168.2.xxx). Is your MBP connected via both WiFi and Ethernet? Because it seems like they're on different internal networks.

Your husband's MacBook seems to be on another 10.0.1.xxx IP address, so that would be why it can connect without a problem.

Hope that helps. :)
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Stefan on December 08, 2008, 04:03:48 PM
UPDATE #2

Since Apple has yet to approve our 1.0.2 for App Store release, I have re-submitted a build to include this additional bug fix, so once 1.0.2 is approved, this issue should be fixed.  8)
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: ChasteDylan on December 19, 2008, 02:25:40 PM
I'm having the same issue as some people on the forum. The rainbow color issue now seems to be resolved for me on vista machines along with failure of analogue video cameras to connect at all, but.... I'm still have fundamental connection issues. Basically, I cannot seem to view streams unless my iphone and all cameras are all connected to the same wifi network. Any cameras on other wifi do give me the connection error message. Also if I connect my iPhone via a different WiFi or Edge and 3g for that mater, I get that same connection issue. I too have reinstalled the app on my phone and all PCs to no avail.

If anyone could give me any guidance I would be greatly appreciative.

Thanks,
Dylan
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on December 20, 2008, 11:14:21 AM
I'm helping Dylan through e-mail.  If info useful for this thread comes out of it,  I'll post it to the thread.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: kahdmus on May 26, 2009, 05:14:49 PM
FYI, Peer Guardian will also block the cellular connection but allow the wifi connection. If you have Peer Guardian either disable or right click on the blocked connection for your iphone and select 'allow permanently. Hope this helps someone..had me stumped for 2 weeks!!!
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 06, 2009, 01:10:40 PM
We have that probl. : Cannot Connect To iCam Broker Server !!!
On wi-hi is all ok.
Is there a solutions.
We are connectec( trying to be ) on PC Windows vista; ( by ethernet )
Pitty it doesnt work.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: Jay on June 06, 2009, 02:51:30 PM
GillNick - The most common reason for that error is a poor wireless connection.  If you see the error consistently when you have a strong wireless signal, the network you're connected to may be blocking UDP traffic. 

Could you go to http://whatismyipaddress.com/ in your computer's web browser to get your computer's IP address, and then send an email to support@skjm.com with the IP address? That way I can attempt to look it up in the iCam Broker Server logs and hopefully troubleshoot the problem.

Please refer to this forum thread in your email.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 07, 2009, 11:59:42 PM
done. sent my IP .
thx
waiting
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 08, 2009, 12:13:53 AM
GillNick  - I replied to all three of your emails, but it seems you're not receiving them.  The last message I sent was:

I found your IP address in the server logs.  I was able to see your iPhone connect from Wi-Fi and from a 3G/EDGE provider named SFR.  Is SFR your service  provider for your iPhone?  The fact that I can see the SFR IP address in the server logs indicates that SFR does not block UDP and that your phone is able to connect to the Broker Server on 3G/EDGE (at least some of the time).  If SFR is your provider, then the Broker Connection Errors you see are due to a poor wireless data connection.

Do you ever see a different error message on your iPhone?  Another common error message when it won't connect from 3G/EDGE is "Source Connection Error".  Have you ever seen that error message?
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 08, 2009, 02:29:37 AM
Yes I am at SFR so as you say they dont block my connection.
No, never an other messege .
When you say it may be due to poor wireless data connection, what connection do you mean ? 
I am "on line" now .
Can you see my place with the login and passworg I gave to you. Mean on 3G.
I dont give up. :)
thx et pls keep on working on my case !
merci
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: Jay on June 08, 2009, 02:35:02 PM
GillNick - Yes, I was able to view your webcam over 3G.

When I say poor wireless data connection, I mean your phone has a poor 3G/EDGE wireless signal.  That is the most common reason for the "Broker Connection Error".  The other possible reason for that error is if your service provider blocks UDP traffic, but your 3G/EDGE IP address shows up in the server logs, so your provider does not block UDP (at least not all of the time).  That leaves poor 3G/EDGE signal as the probable reason for that error.

Have you ever tried connecting to your webcam from a Wi-Fi hotspot (not your home Wi-Fi)?  If so, did it work?
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 09, 2009, 12:34:49 AM
I will try to connect that way ( hotspot, or cyber café ) .
  What we ( 2 iphones ) did till now was to try to connect from our willage, where I know that the 3G is poor, than also wrom an other place, small town next to us, than also in Paris on two diferent locations. We never had one single connection.
Opening one port in my router? Could it help ?
Change the provider ?
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 09, 2009, 11:20:28 AM
GillNick - Unfortunately, opening the ports won't help with a Broker Connection Error because that error means that your phone is unable to communicate with the Broker Server, so your home computer isn't involved with that error at all.  If you were seeing a "Source Connection Error" then opening ports might help.

The Broker Connection Error either means that your iPhone has poor 3G/EDGE signal or that your service provider blocks UDP traffic.  Either way, it is an issue with your wireless service provider (as opposed to your home network, etc.).   A different provider might work better, but if the signal is poor with that new provider as well, you might have the same problem.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 09, 2009, 12:55:52 PM

I verified on tha card of 3G cuvering for France.
Yes I am in a poour 3G district. I mean my willage.
But I was trying to connect from the areas with the good 3G receiving according to the official Wi-Fi, 3G : Paris and some other towns too.
So I think it "MUST" depend on provider. ( blocking etc )
 You asked me to try to use WI-FI hot spot . I will do it and report here ( not only for me but for the others with similar problems ) .
thx


Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 09, 2009, 03:00:07 PM
You may be right about the provider blocking UDP.  As I mentioned before, I was able to find SFR IP addresses in the server logs, but SFR may have several different networks and apply different blocking rules on each network.  That would explain the Broker Connection Error showing up for you, even in strong signal areas.  We haven't heard any reports from other users with issues connecting on SFR, but I don't know how many iPhone users there are on SFR.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 11, 2009, 06:00:46 AM

Here is the message I had by hot spot connecting :

Your nework may be preventing from making UDP connections to iSam broker server .


Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 11, 2009, 10:21:11 AM
I looked in the server logs for the IP address you sent me earlier.  I see several connections from SFR IP addresses today, so you should not be seeing the Broker Connection Error when you're connected to SFR.  Is it working for you today, or are you seeing a different error message when your iPhone is connected to SFR?
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 11, 2009, 12:56:20 PM
No, no I could NEVER connect to iCam . NEVER !!!
With two iphones and from several towns . Today I tried to connect from one hot spot, as you asked me to do, on wi fi.
I could not . I had this message :

"Your nework may be preventing from making UDP connections to iSam broker server .
pls contact support .... and so on , and so on "

Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 11, 2009, 02:08:42 PM
only on wi fi next to my PC  you might see this connections
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 11, 2009, 02:26:44 PM
I do see your iPhone connecting from your local wi-fi, but I also see the iPhone connecting using IP addresses that are owned by SFR.

If you are getting "Broker Connection Error" messages every single time you connect while your phone is on SFR, then SFR is blocking incoming UDP traffic.  I can see SFR IP addresses in the server logs, so they aren't blocking outgoing UDP traffic.

If this is the case, this is the first time we've seen a service provider allow outgoing UDP and block associated incoming UDP packets.  I would suggest you contact SFR and confirm whether or not they allow UDP communication over their mobile network.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 12, 2009, 12:17:18 AM

I will do it !!!
I also changed  my abonement at SFR
I subscribed a new abonement named  : Forfait Illimythics 3G+ Full Internet
So it starts 21 of this month which means : I ll give you a break till than  :)
thx
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 12, 2009, 10:28:43 AM
I hope the new service plan works out better for you.  If the new plan is with SFR, it may still have the same problem because the issue might be with their router settings and not necessarily the features of the service plan.

The only French networks we have any information about are Orange and Bouygues.  We have heard from users that iCam works well on the Orange network.  We've heard a couple reports of problems with Bouygues, but we haven't been able to confirm them.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 12, 2009, 01:28:58 PM
Yes but I can not change the provider for the moment. The moment is long : 1 year ! :)
What could I test more to be sure that they block some of UDP ?

My Internet provider ( it is also sfr ) has nothing to do with my problem ?

Thx
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 12, 2009, 04:11:47 PM
There really isn't any different test that we can do.  In this case, since you are seeing the Broker Connection Error, but the Broker Server does see your phone, that means that the UDP messages that the server is sending back to your phone are not being received and that they are being blocked by your service provider.

Your home internet connection doesn't have anything to do with this particular error because it is the connection between the phone and the Broker Server that has the problem.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 17, 2009, 09:01:24 AM
I come back to the idea to open the port in my router. Can you , pls, give me the port which can be used for iCam;
Thx
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 17, 2009, 11:26:41 AM
Opening the ports in your router won't help if you're only seeing the Broker Connection error.  It might help if you're seeing the Source Connection Error.

There is information about setting up port forwarding in this forum post: http://skjm.com/forum/index.php?topic=182.msg644#msg644

If you have any questions about the information in that post, please let me know.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 22, 2009, 02:34:16 AM


Jay

just give me the port please.

thx
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on June 22, 2009, 10:18:45 AM
GillNick - The port forwarding information, including the ports, is in the forum post I linked to before.  http://skjm.com/forum/index.php?topic=182.msg644#msg644

If you have any questions about the information in that post, please let me know.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on June 23, 2009, 03:57:11 AM
Thx  Will do my tests   
You ll have my report about ( and event.questions )
waiting for some connections changes
it will take about a week
so till then
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on July 07, 2009, 06:36:37 AM
IT WORKS  !!!!!
It was not the question of port in the router. I tested that but could not connect.
I can connect now even in Edge arias.
I just have better upload now !!! The only factor that changed after what I connect easyly every where.

I am happy about that !!!!
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on July 07, 2009, 03:10:37 PM
I'm glad it's working for you!
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on July 08, 2009, 05:01:31 AM

I was glad and happy  but I have again : Source Connection Error !!!!!!

Same here in edge as well in Paris in 3G, or even WI-FI point in the town    : One or more of the iCam Broker Server retourned by the Icam Server could not be connected to !!!!!

It begions to be sad and LOL !!!!!!
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on July 08, 2009, 08:57:38 PM
I'm sorry to hear that.

I looked back through the previous posts.  Before you were getting Broker Connection Error messages, but now you're getting a Source Connection error, is that correct?  If so, please email your computer's IP address (from whatismyip.com) to support@skjm.com.  I'll reply to you here on the forum, because I remember you weren't receiving my emails before. 
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on July 09, 2009, 04:22:21 PM
GillNick - I sent an email to you a few hours ago.  If you didn't get it, please let me know.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: GillNick on July 10, 2009, 05:45:03 AM


No i did not. Strange . Not easy receiving iCam !   :)
Even e mails. lol

Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: alanowl on July 10, 2009, 07:14:45 AM
i'm getting the same "broker connection error" msg. can you tell me how you solve it? i'm connecting icam thru icam web. icamsource was set on my house on another city. i try to connect to icam when i go to my wife's house at another city thru her house wi-fe network. any solution?
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on July 10, 2009, 12:22:25 PM
GillNick -  Yeah, you didn't receive my emails before, so I figured you wouldn't this time either.  Do you have another email address available?  If so, could you please email it to suppport@skjm.com?  I'd rather not post IP address and login information on the forum.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: Jay on July 10, 2009, 12:25:12 PM
alanowl is getting technical support for this issue through email.  If there is any new information about this issue from the emails, I'll post it in this thread.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: gpvirzi on July 11, 2009, 02:18:42 PM
Hello,

I have sent an email to the support email about this same problem:
Source Connection Error
One or more of the icamSources returned by the iCam Broker Server could not be connected to.

It happens only on Edge, not on WiFi.
If I press repeatedly the Refresh button on the iCam App I can usually get it to work after a while, but usually not all 3 cams.

I tried launching the Weather or the Stocks app before staring iCam but that does not seem to work.

Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: Jay on July 11, 2009, 05:46:24 PM
gpvirzi is getting technical support for this issue through email.  If there is any new information about this issue from the emails, I'll post it in this thread.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: gpvirzi on July 13, 2009, 07:15:45 AM
Update:

My issue was solved after Port Forwarding.

Thanks Jay!.

Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: RedSunflower on July 19, 2009, 09:14:17 PM
Success!!!!!!! :D ;D :D ;D

Wee!!!!!  After communicating with Jay and Stefan (thank you, thank you, thank you) I just got bold and decided to read through some of the "fixes".  I did this one and it works!!!!  If you're courageous...go for it.
http://skjm.com/forum/index.php?topic=182.msg644#msg644
My iPhone and iCam on an iMac are now communicating.

Now, I want to get another camera to add to the mix.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: dirtymexican on July 19, 2009, 09:51:43 PM
 same here getting (source connection error) i have tried it about 50 times its not working, please help
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: dirtymexican on July 19, 2009, 10:00:16 PM
well i didnt tell that much last reply, i bought this app today, i have full bars 3g, any solutions thx
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.
Post by: Jay on July 20, 2009, 12:21:11 AM
Technical support for this issue is being handled through email.  If there is any new information about this issue from the emails, I'll post it in this thread.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: HeyJB on May 17, 2010, 03:39:23 PM
It seems like this hasn't been an issue for people for a while, but I'm having issues.

I'm using my mac powerbook with an external webcam. I downloaded the latest version of the software yesterday. I was able to view the icam source on my ipod touch at home on my wifi in the same room, as well as others. However, when I got to work, it says it can't connect to the iCam Broker Server.

I can watch the feed online at http://skjm.com/icam/web/ and I'm getting push notifications, but it's not pulling up the stream and I can't see the Motion Events images. I'm using my work's wifi, so I'm not sure if that's the issue or not.

I tried to open weather and stocks and mail, and then go back to iCam and it's still giving me the same info.

Thanks!
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: OUAnthony on May 17, 2010, 06:20:34 PM
Your employer is either blocking communication with your home IP address, or with the broker server. My employer, a public school, has an aggressive firewall that blocks pretty much everything (or so it seems). I have the same issues as you. Are you able to connect with 3g? Try turning off your wireless at work and see if you can view it again.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: davidwaynea0 on March 05, 2011, 08:20:59 AM
Guys for the people who cant seem to connect to the cameras using their iphones over 3g, go to your computer and open the icamsource preferences. after you see the panel open up go to the bottom left corner and tick the "Auto-Config Router". start up the video again. and it should work fine. If it doesn't, leave it checked, and reboot your computer and phone, and try again. hope it helps.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: davidwaynea0 on March 05, 2011, 08:23:48 AM
Just tick the bottom left corner on the preferences of icamsource. "Auto config router"
reboot both computer and phone. it should work perfectly after that.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: OUAnthony on March 05, 2011, 12:32:02 PM
Also make sure you have uPNP enabled in the router settings if attempting to use the "Auto config router" setting in icamsource.
Title: Re: "Cannot Connect To iCam Broker Server" on EDGE or 3G - Fix coming in iCam 1.0.2
Post by: CID420 on August 24, 2011, 05:40:22 AM
I need help with something. icam works perfectly for my meaning i have icam on my tablet and icam source on my comp. but my other laptop cannot view the cameras from the website. it says 2 sources on my laptop, but no feed. i can see them perfectly on my pc and my galaxy tab at the sametime. but for some reason i can't get it to work on my laptop.
i have uPNP enabled and also tried auto config router and restarted everything... still nothing.

Please If You Can Email Me At:
Marmalademan420@hotmail.com